Home / Axles

Identify it before you build it

Axles: Dana 30, 35, 44 and the swaps people talk about

Factory patterns by generation, how to read a cover and a tag, and an honest note on Dana 60s.

The axle under a Wrangler is not always the one the brochure listed when it was new. Start with the cover shape and the tag, then compare that to the generation and trim.

How to identify an axle

Quadratec’s Wrangler axle guide, written for owners who may not want to crawl under the Jeep first, uses differential-cover shape as a first look:

  • Dana 30: flat sides with a round top and bottom. On Wranglers, Quadratec says this axle was only used in the front, so you will not find a factory Dana 30 in the rear.
  • Dana 35: an oval cover, wider than it is tall. Quadratec says this one is a rear axle on Wranglers, not a front.
  • Dana 44: flat sides with a more angular top and bottom, used in front or rear.

The more reliable confirmation is the bill of material number stamped on the axle tube. Quadratec describes it as six digits followed by one or two more at the end of the tube; Dana’s own lookup is how you decode it. A used Jeep can also be checked against a factory build sheet through the VIN on Jeep’s site, which tells you what it was born with, not what is under it now.

Dana 30, 35 and 44

From the first YJ through the current JL, Quadratec says Jeep has featured three main factory varieties of Dana solid axles on Wranglers: the 30, 35 and 44. The 44 is the heavier of those three factory housings and is the one Jeep listed on Rubicon models. Later JL axles, Quadratec notes, are stronger and lighter than earlier ones and are not interchangeable with earlier-generation 30s, 35s or 44s even when they share a name.

A cover shape is a start, not a complete identification. Aftermarket covers, swapped axles, and “Rubicon 44” versus earlier 44 housings are all reasons to read the tag.

Typical factory combinations

These are the factory patterns described by Quadratec and, where we have them, by Jeep or Stellantis fact sheets. They apply to original equipment, not to a Jeep that has already been built.

PlatformTypical factory frontTypical factory rearSource notes
YJ (1987–1995)Dana 30Dana 35Quadratec: Jeep offered only this factory combination on the YJ.
TJ, non-RubiconDana 30Usually Dana 35; Dana 44 rear optional on some manuals, per QuadratecQuadratec. Jeep’s official TJ years are 1997–2006 (Quadratec’s page starts the TJ table at 1998).
TJ Rubicon (2003–2006)Dana 44Dana 44Jeep history and the 2003 Stellantis Rubicon press kit: Dana 44 axles front and rear.
LJ UnlimitedDana 30, per QuadratecDana 44, per QuadratecQuadratec. Confirm on the vehicle; a 2005 Rubicon Unlimited would have been listed with Rubicon axle equipment.
JK Sport / SaharaDana 30Dana 44 (most); some early two-doors had a Dana 35 rear2018 JK fact sheet: Dana 30 front, Dana 44 rear on Sport and Sahara. Quadratec: early two-door 35 rear, then a switch; all original four-doors have a Dana 44 rear.
JK RubiconDana 44Dana 44Quadratec. Confirm lockers and tags on a used Jeep.
JL, non-RubiconDana 30, per Quadratec (“next-generation Dana” in Stellantis language)Dana 35, per QuadratecStellantis fact sheets say “next-generation Dana front and rear axles” on Sport and Sahara. Quadratec names 30 / 35 and warns they are not interchangeable with older housings.
JL Rubicon and Gladiator RubiconDana 44Dana 44Stellantis fact sheets: Dana 44 front and rear heavy-duty axles on JL Rubicon; later Gladiator materials describe the same family of hardware.

XJ Cherokees, as summarized in the XJ technical literature, typically use a Dana 30 front on 4x4s; rears vary (commonly discussed options include the Chrysler 8.25 and Dana 35). Identify the rear on the housing rather than assuming from the model year.

Dana 60 swaps

Dana Super 60 front axle housing
A Dana Super 60 front housing, the kind of heavy axle builders swap into built 4x4s. This is not a factory Wrangler axle. Photo: Dana60Cummins, public domain, via Wikimedia Commons.
Dodge Off Road Dana 60 differential cover
DOR’s Dana 60 cover is listed for 1994–2002 Ram Dana 60s, not as a Jeep factory part. Photo: Dodge Off Road product photo.

Quadratec is direct: a Dana 60 is not a stock axle on any Wrangler trim. Owners who want a heavier housing sometimes swap one in. That is a custom axle swap, with width, brakes, steering knuckles, springs and driveline angles all to be designed for that Jeep. This site does not provide swap dimensions or a parts list for that work.

If a donor axle happens to be a 1994–2002 Ram Dana 60, Dodge Off Road lists a Dana 60 differential cover for those Ram housings. It is not listed for Jeep factory axles, and it is not listed for every Dana 60 ever made. Details are on the DOR parts page.

Confirm, do not assume

  1. Read the cover shape, then the bill of material stamp or a clean photo of the tag.
  2. Compare that to the generation and trim, using the table above as a first guess only.
  3. On a used Jeep, look for mismatched rear and front covers, fresh welds, or a previous owner who already swapped axles.
  4. If you are buying parts, the parts maker’s fitment list — not a forum memory of “all TJs” — is what counts.

Factory Rubicon lockers, transfer cases and sway-bar disconnects are covered on the Rubicon page. Lift geometry that depends on these axles is on lifts and geometry.

Where this comes from

Last reviewed 2026-11-10. General information only: the vehicle maker’s and your parts maker’s instructions come first.